CamFeatureItemID 说明：
以Sp开头的ID为特别指定的ID号，在使用中配合独有的动作处理，不能乱改

ID	描述	备注
SpHotRunnerGroup	发热管组里专门加工倒扣面	与HotRunnerGroup特征一起使用
FacePlateFacesArea1	面板特征精加工	与FacePlateFaces1特征一起使用
FacePlateFacesArea2	面板特征精加工	与FacePlateFaces1特征一起使用
FacePlateFacesArea3	面板特征精加工	与FacePlateFaces1特征一起使用
FacePlateFacesArea4	面板特征精加工	与FacePlateFaces1特征一起使用
FacePlateFacesArea5	面板特征精加工	与FacePlateFaces1特征一起使用
FacePlateFacesArea6	面板特征精加工	与FacePlateFaces1特征一起使用
AutoFacePlate	封闭的平底框面板专用策略	根据面板的特征自动分析并执行相应的加工策略

示例：
SpHotRunnerGroup：

FacePlateFacesArea1：

FacePlateFacesArea2：

FacePlateFacesArea3:

FacePlateFacesArea4:

FacePlateFacesArea5:

FacePlateFacesArea6：

FacePlateFacesArea7:

FacePlateFacesArea8:

FacePlateFacesArea9:

FacePlateFacesArea10:

FacePlateFacesArea11:

FacePlateFacesArea12:

FacePlateFacesArea13:

FacePlateFacesArea14:

FacePlateFacesArea15:

FacePlateFacesArea16:

FacePlateFacesArea17:

FacePlateFacesArea18:没有耳朵位的框

FacePlateFacesArea19:与17的区别是耳朵位与框齐高

FacePlateFacesArea20

FacePlateFacesArea21

FacePlateFacesArea22 斜面区域

FacePlateFacesArea23

热流道板
HotRunnerPlateFacesArea1

HotRunnerPlateFacesArea2

HotRunnerPlateFacesArea3

HotRunnerPlateFacesArea4

HotRunnerPlateFacesArea5

HotRunnerPlateFacesArea6 半径等于7.5或12.5

HotRunnerPlateFacesArea7 半径小于3

HotRunnerPlateFacesArea8

HotRunnerPlateFacesArea9

HotRunnerPlateFacesArea9_1

HotRunnerPlateFacesArea10

HotRunnerPlateFacesArea11

HotRunnerPlateFacesArea12

HotRunnerPlateFacesArea13

HotRunnerPlateFacesArea15

HotRunnerPlateFacesArea16: 除了HotRunnerPlateFacesArea2和HotRunnerPlateFacesArea4及HotRunnerPlateFacesArea3底部以下的区域，某些情况下相当于HotRunnerPlateFacesArea3

HotRunnerPlateFacesArea17: 除了HotRunnerPlateFacesArea3底部以下的区域

HotRunnerPlateFacesArea18: HotRunnerPlateFacesArea3的最低底平面

HotRunnerPlateFacesArea19: 反面的框

HotRunnerPlateFacesArea20: 底下整个区域

HotRunnerPlateFacesArea21: 19_1以下的区域/排除反面的框

LetterMark1:

LetterMark2

PlaneGrooveFacesArea1 带避空角的方框

PlaneGrooveFacesArea2 带避空角的D框

IncludingChamfers:通常是用在平底框上

EscapeHole避空孔